Welded Austenitic Tubes for Heat Exchangers, Condensers and Boilers
ASTM A249 / ASME SA249 tubes are welded austenitic stainless steel tubes for boilers, superheaters, heat exchangers and condensers. They are made from strip by automatic welding without filler metal, cold worked at the weld, solution annealed and fully tested, and are ordered by outside diameter and nominal wall (often in BWG).
Dinesh Tube India supplies A249 tubes in TP304/304L, TP316/316L, TP317L, TP321, TP347, H grades and 904L, in straight lengths or U-bent, with EN 10204 3.1 certificates and third-party inspection on request. We are a supplier and exporter based in Mumbai. For seamless tubes see our stainless steel tubes range.
A249 Tube Specification
| Item | Details |
|---|---|
| Standard | ASTM A249 / A249M; ASME SA249 (general requirements ASTM A1016) |
| Product | Welded (WLD) or heavily cold worked (HCW) welded tubes |
| Size range usually furnished | 3.2 mm (1/8") ID to 304.8 mm (12") OD; wall 0.4 to 8.1 mm (0.015" to 0.320") |
| Common HX sizes | 9.52, 12.7, 15.88, 19.05, 25.4, 31.75 and 38.1 mm OD; BWG 12 to 20 |
| Lengths | Straight lengths to drawing (commonly up to about 20 m); U-bent on request |
| Condition | Solution annealed; bright annealed or annealed and pickled |
| Ends | Plain square cut, deburred; end caps |
A249 Grades and UNS Numbers
| Grade | UNS | Typical use |
|---|---|---|
| TP304 / TP304L / TP304H | S30400 / S30403 / S30409 | General heat exchangers, food and water service; H for high temperature |
| TP316 / TP316L / TP316H | S31600 / S31603 / S31609 | Chloride-bearing and chemical service |
| TP317L | S31703 | More molybdenum for acids and FGD |
| TP321 / TP321H | S32100 / S32109 | Titanium-stabilised, elevated temperature |
| TP347 / TP347H | S34700 / S34709 | Niobium-stabilised, superheaters |
| TP310S / TP309S | S31008 / S30908 | High-temperature oxidation |
| 904L | N08904 | Sulphuric acid, seawater-cooled exchangers |
| 6Mo (254 SMO) | S31254 | Seawater and high-chloride condensers |
Common BWG Wall Thicknesses
| BWG | 10 | 12 | 14 | 16 | 18 | 20 | 22 |
|---|---|---|---|---|---|---|---|
| Wall (mm) | 3.40 | 2.77 | 2.11 | 1.65 | 1.24 | 0.89 | 0.71 |
| Wall (in) | 0.134 | 0.109 | 0.083 | 0.065 | 0.049 | 0.035 | 0.028 |
A249 tubes are ordered to nominal (average) wall; wall and OD tolerances follow ASTM A1016.
Chemical Composition (%), ASTM A249 Table 1
| Grade | C max | Mn max | P max | S max | Si max | Cr | Ni | Mo | Other |
|---|---|---|---|---|---|---|---|---|---|
| TP304 | 0.08 | 2.00 | 0.045 | 0.030 | 1.00 | 18.0–20.0 | 8.0–11.0 | – | – |
| TP304L | 0.030* | 2.00 | 0.045 | 0.030 | 1.00 | 18.0–20.0 | 8.0–12.0 | – | – |
| TP304H | 0.04–0.10 | 2.00 | 0.045 | 0.030 | 1.00 | 18.0–20.0 | 8.0–11.0 | – | – |
| TP316 | 0.08 | 2.00 | 0.045 | 0.030 | 1.00 | 16.0–18.0 | 10.0–14.0 | 2.00–3.00 | – |
| TP316L | 0.030* | 2.00 | 0.045 | 0.030 | 1.00 | 16.0–18.0 | 10.0–14.0 | 2.00–3.00 | – |
| TP316H | 0.04–0.10 | 2.00 | 0.045 | 0.030 | 1.00 | 16.0–18.0 | 10.0–14.0 | 2.00–3.00 | – |
| TP317L | 0.030 | 2.00 | 0.045 | 0.030 | 1.00 | 18.0–20.0 | 11.0–15.0 | 3.0–4.0 | – |
| TP321 | 0.08 | 2.00 | 0.045 | 0.030 | 1.00 | 17.0–19.0 | 9.0–12.0 | – | Ti 5×(C+N) to 0.70; N 0.10 max |
| TP347 | 0.08 | 2.00 | 0.045 | 0.030 | 1.00 | 17.0–19.0 | 9.0–12.0 | – | Nb 10×C to 1.10 |
| N08904 | 0.020 | 2.00 | 0.040 | 0.030 | 1.00 | 19.0–23.0 | 23.0–28.0 | 4.0–5.0 | Cu 1.00–2.00; N 0.10 max |
| S31254 | 0.020 | 1.00 | 0.030 | 0.010 | 0.80 | 19.5–20.5 | 17.5–18.5 | 6.0–6.5 | N 0.18–0.25; Cu 0.50–1.00 |
*Slightly higher carbon is allowed for small-diameter or thin-wall L-grade tubes under a Table 1 footnote. H grades also have grain-size requirements. The edition on the order and the mill certificate govern.
Tensile and Hardness Requirements
| Grade | Tensile min | Yield min | Elongation in 50 mm min | Hardness max |
|---|---|---|---|---|
| TP304, TP304H, TP316, TP316H, TP317L, TP321, TP347, TP309S, TP310S | 515 MPa (75 ksi) | 205 MPa (30 ksi) | 35% | 90 HRB |
| TP304L, TP316L | 485 MPa (70 ksi) | 170 MPa (25 ksi) | 35% | 90 HRB |
| N08904 | 490 MPa (71 ksi) | 215 MPa (31 ksi) | 35% | 90 HRB |
| S31254 | 675 MPa (98 ksi) | 310 MPa (45 ksi) | 35% | 96 HRB |
Values as tabulated in ASTM A249 Table 3 for annealed tube; Vickers hardness may be used for very small or thin tubes. Confirm against the edition named in your order.
Manufacture and Heat Treatment
- Formed from flat-rolled strip and welded by an automatic process without filler metal.
- The weld (or weld and base metal) is cold worked before final heat treatment to refine the weld structure; heavily cold worked (HCW) tubes get at least 35% reduction after 100% radiography of the weld.
- Every tube is solution annealed: 1040 °C (1900 °F) minimum for most grades, 1100 °C for TP321H, TP347H and 904L, and 1150 °C for S31254, followed by rapid cooling.
Required Tests
- Tension test per lot
- Flattening and flange tests on specimens from each end of finished tubes per lot
- Reverse bend test of the weld, one per 450 m (1500 ft) of tubing (not required for heavy walls or OD under 9.5 mm)
- Hardness test on two tubes per lot
- Hydrostatic or nondestructive electric test on every tube, per A1016
- Optional: eddy current plus hydro, intergranular corrosion test (A262), ultrasonic weld test, PMI and third-party inspection
A249 vs A213 vs A269
| Point | ASTM A249 | ASTM A213 | ASTM A269 |
|---|---|---|---|
| Process | Welded | Seamless | Seamless or welded |
| Intended use | Boilers, superheaters, heat exchangers, condensers | Boilers, superheaters, heat exchangers | General corrosion-resisting service, instrument lines |
| Testing | Tension, flatten, flange, reverse bend, hardness, hydro/NDE | Tension, flatten, flare, hardness, hydro/NDE | Lighter: hardness, flare, flange, hydro/NDE |
| Wall basis | Nominal | Minimum or average, as ordered | Nominal |
| Typical cost | Lower than seamless | Higher | Lowest |
Applications
- Shell-and-tube heat exchangers in refineries, petrochemical and chemical plants
- Surface condensers and feedwater heaters in power plants
- Superheater and reheater tubes in H grades
- Food, dairy, beverage and pharmaceutical heat exchangers
- Evaporators, coolers and process heaters
How to Order A249 Tubes
State the specification (ASTM A249 or ASME SA249 and edition), grade, OD, wall (mm or BWG), length, quantity, straight or U-bent (with bend radii), finish, optional tests (eddy current, A262, ultrasonic), certification and inspection, and delivery location.
Need A249 welded tubes? Send your tube list to kamlesh@dineshtube-india.com or call +91 83559 10913. You can also send an enquiry.
Related Products
Stainless steel tubes, heat exchanger tubes, boiler tubes, SS 304 welded micro tubes, SS 316 welded micro tubes and all stainless steel products.
ASTM A249 Tubes: FAQs
What is ASTM A249?
ASTM A249 (ASME SA249 for code work) is the standard for welded austenitic stainless steel tubes for boilers, superheaters, heat exchangers and condensers. Tubes are made from flat-rolled strip by automatic welding without filler metal, the weld is cold worked, and every tube is solution annealed.
What is the difference between A249 and A213?
A213 covers seamless tubes; A249 covers welded tubes in similar austenitic grades with the same tensile requirements. Welded A249 tube is usually cheaper and has very uniform wall thickness, so it is widely used for heat exchangers and condensers. Some codes and high-pressure duties still require seamless A213.
What is the difference between A249 and A269?
A249 is for pressure-retaining boiler, heat exchanger and condenser tubes and includes tension, flattening, flange, reverse bend and hardness tests. A269 is a general-service standard for seamless and welded tubing with lighter testing, used for instrument and process lines.
Which sizes does A249 cover?
Tubes usually furnished to A249 range from 3.2 mm (1/8 in) inside diameter to 304.8 mm (12 in) outside diameter, with walls from 0.4 to 8.1 mm (0.015 to 0.320 in). Heat-exchanger tubes are most often 15.88 to 25.4 mm (5/8 to 1 in) OD in BWG 14 to 18.
Which grades are available to A249?
Common grades are TP304, TP304L, TP304H, TP316, TP316L, TP316H, TP317L, TP321, TP321H, TP347, TP347H, TP309S and TP310S, plus higher alloys such as 904L (N08904) and 6Mo S31254. Dual-certified TP304/304L and TP316/316L are the most common stock items.
