ASME SA179 / ASTM A179 Specification Summary
This page summarises the requirements of ASME SA179 / ASTM A179, Seamless Cold-Drawn Low-Carbon Steel Heat-Exchanger and Condenser Tubes. ASME SA179 is identical to ASTM A179 and is used for ASME code equipment. Always check the edition named in your purchase order.
To buy tubes, see our ASME SA179 carbon steel tubes page. A printable version is available as the ASTM A179 tube specification sheet (PDF).
Scope of SA179
| Item | Requirement |
|---|---|
| Title | Seamless cold-drawn low-carbon steel heat-exchanger and condenser tubes |
| Product | Minimum-wall-thickness tubes for tubular heat exchangers, condensers and similar heat-transfer equipment |
| Size range | 1/8 in to 3 in (3.2 to 76.2 mm) outside diameter, inclusive |
| Small sizes | Mechanical property requirements do not apply below 1/8 in (3.2 mm) OD or 0.015 in (0.4 mm) wall |
| General requirements | ASTM A450 / ASME SA450 |
| Units | Inch-pound unless the A179M (SI) designation is ordered |

Manufacture and Heat Treatment
SA179 Chemical Composition (%)
Supplying an alloy grade that requires deliberate additions of other elements is not permitted. Product analysis tolerances follow A450.
Hardness and Design Properties
Many supplier pages list the tensile values as test requirements. In SA179 the only mandatory mechanical property limit is hardness.
Dimensional Tolerances (ASTM A450, Cold-Drawn Seamless)
Values from ASTM A450 for cold-finished seamless tubes; check the edition on your order. Thin-wall tubes may show additional ovality as allowed by A450.
Required Tests
A lot is defined in the specification by size, heat and heat-treatment batch. Supplementary requirements may be added by agreement.
Related Tube Grades
Ordering Information
An SA179 order should state: quantity; name of material (seamless tubes); manufacture (cold drawn); size (OD and minimum wall); length (specific or random); test track (hydrostatic or NDE); certificates (EN 10204 3.1 or as required); and any supplementary requirements.
Need SA179 tubes? Send your OD, minimum wall, length and quantity to kamlesh@dineshtube-india.com or call +91 83559 10913, or see the SA179 tubes product page.
SA179 Specification: FAQs
What does the SA179 specification cover?
ASME SA179 (identical to ASTM A179) covers minimum-wall-thickness, seamless cold-drawn low-carbon steel tubes for tubular heat exchangers, condensers and similar heat-transfer equipment, in sizes from 1/8 in to 3 in (3.2 to 76.2 mm) outside diameter.
Does SA179 have a minimum tensile strength?
Not as a test requirement. The specification requires a maximum hardness of 72 HRB, plus flattening, flaring, flange and pressure tests. It gives tensile strength 325 MPa, yield strength 180 MPa and elongation 35% only as values that may be assumed for design.
Can SA179 tubes be welded or hot finished?
No. SA179 tubes must be seamless and cold drawn, and heat treated at 650 °C (1200 °F) or higher after the final cold draw. Welded heat-exchanger tubes in similar steel are covered by SA214, and welded boiler tubes by SA178.
What is the difference between SA179 and SA192?
Both are seamless low-carbon steel tubes with the same carbon and manganese limits. SA179 is for heat exchangers and condensers up to 3 in OD with 72 HRB maximum hardness, while SA192 is for high-pressure boiler tubes up to 7 in OD, adds a 0.25% silicon limit and allows 77 HRB / 137 HB.
How are SA179 tube tolerances specified?
Dimensional tolerances come from the general-requirements specification ASTM A450 / ASME SA450. Because SA179 is a minimum-wall specification, the wall may be over the ordered minimum but not under it.
This is a summary for reference only. ASTM A179/A179M and ASME SA-179 are copyrighted standards; the purchased standard and the edition on the order govern.